Descaling Liquid

Acid Descaler for Water Scale and Rust Deposits

PART # EA01 | 0731851223835

PHYSICAL DATA

Appearance: Aqueous red

Specific gravity: 1.15 @20°C

Flash Point: None

pH (1% solution): 1.0

DESCRIPTION

Liquid acid compound containing descaling accelerators and corrosion inhibitors.

• Removes hardness scale from water systems
• Removes rust and rust scale from ferrous metals (except stainless steel)
• Improves heat transfer efficiency
• Inhibited against attack on ferrous metals

APPLICATION

• Removal of hardness scales from boilers, condensers, evaporators, heat exchangers, diesel engine cooling systems, air coolers sea water side, etc.
• Removal of rust scale from all ferrous metal surfaces

ADVANTAGES

• Fast and efficient scale removal
• Complete rust removal
• Contains descaling accelerator to increase product action
• Contains protective corrosion inhibitor: inhibits attack on ferrous metals
• Highly concentrated product: rapidly rinsed
• In-situ cleaning eliminates need for extensive dismantling

DIRECTIONS FOR USE

Descaling can be accomplished by circulation, for large components and systems, by in-situ soaking, or by soaking in an immersion bath for small components. The most effective method is by circulation as it ensures renewal of acid film in contact with the scale.

Circulation method:

1. If deposits to be removed are covered with an oil or grease film, a degreasing treatment with a solution of 2% to 8% of ALKACLEAN, CARBON REMOVER, SEACLEAN with water should be used prior to descaling, by circulating for 4 to 6 hours up to a temperature of 60°C.
2. After degreasing (where necessary) a descaling treatment of a solution of 10% to 20% of DESCALING LIQUID with water should be circulated for between 24 to 36 hours for hardness scale, and 1 to 4 hours for de-rusting, depending on nature and state of deposits.
3. Ensure circuit is vented at the highest point to release gases produced during the descaling operations.
4. Product solution may be heated to increase the descaling process rate. DO NOT EXCEED 40°C as chlorine gas may be liberated above this temperature.
5. Check the acid concentration of the solution regularly. If it drops to less than 1/2 initial concentration, regenerate the solution by adding more DESCALING LIQUID.
6. Determination of the concentration may be found using an Acidity Test Kit (obtainable from Uniservice Unisafe).
7. By placing scale samples in easily observed positions, a check on the progress of the descaling operation may be made. When the samples are completely dissolved and effervescence has stopped, circulate for one more hour then drain system thoroughly.
8. Rinse system thoroughly with water then drain.
9. To neutralize any remaining traces of acid and to passivate the circuit, circulate a 1% to 2% by weight solution of ALKALINITY CONTROL for 2 to 6 hours.
10. Neutralize acidic effluents drained from the descaling solutions by using ALKALINITY CONTROL until an acceptable pH value is obtained.

Soaking Method:

• Procedure is similar to that for circulation, i. e. Degreasing, Descaling (ensuring venting), Rinsing and Neutralization.
• The same solution strength should be used.
• If agitation of the descaling solution can be practiced, this will help to renew the acid film coming into contact with the scale.

Please download Technical Information PDF at link in product's card.

© 2023 Uniservice Unisafe Srl | Marine Chemicals division | www.uniservicemarine.com | Email | T (+39) 010.711.395 | F (+39) 010.713.120

IMPORTANT NOTICE: While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, this information is provided for your guidance only. Because many factors may affect processing or application/use, we recommend that you do a test to determine the suitability of a product for your particular purpose prior to use. No warranties of any kind, either expressed or implied, including warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth, or that the products, designs, data or information may be used without infringing the intellectual property rights of others. In no case shall the descriptions, information, data or designs provided be considered a part of our terms and conditions of sale. Further, you expressly understand and agree that the descriptions, designs, data and information furnished by Uniservice Unisafe Srl hereunder are given gratis, and Uniservice Unisafe Srl assumes no obligation or liability for the description, designs, data and information given or results obtained, all such being given and accepted at your risk.

Ultrasafe Descaling Liquid

Liquid Safe Descaler

PART # EA02 | 0731851223842

PHYSICAL DATA

Appearance: Colorless liquid

Specific gravity: 1.430 kg/L

Solubility in water: Complete

pH solution w/ water: <2

DESCRIPTION

Water soluble descaling compound based on diphosphonic acid and corrosion inhibitors.

• Easily dissolves water scale.
• Works either in hot or cold water.
• Improves heat transfer.
• Safe on steel, iron and several alloys.
• Non toxic, non explosive.
• At the end of descaing reaction tends to flocculate the scale particulate.

APPLICATION

• Descaling of diesel engine cooling systems.
• Cleaning and scale removal from coolers sea water side.
• Water scale removal from boilers, heat exchangers, boilers, evaporators etc.
• Especially blended for new MSF evaporators

DIRECTIONS FOR USE

Descaling can be accomplished by circulation, for large components and systems, by in-situ soaking, or by soaking in an immersion bath for small components. The most effective method is by circulation as it ensures the renewal of acid film in contact with the scale.

Soaking Method:

• Procedure is similar to that for circulation, i. e. Degreasing, Descaling (ensuring venting), Rinsing and Neutralising.
• The same solution strength should be used.
• If agitation of the descaling solution can be practised, this will help to renew the acid film coming into contact with the scale; agitation can be brought by the use of small flow of compressed air

Circulation method:

1. If deposits to be removed are covered with an oil or grease film, a degreasing treatment with a solution of 2% to 8% of ALKACLEAN, CARBON REMOVER, SEACLEAN with water should be used prior to descaling, by circulating for 4 to 6 hours up to a temperature of 60°C.
2. After degreasing (where necessary) a descaling treatment of a solution of 3% to 5% by weight of ULTRASAFE DESCALING LIQUID with water should be circulated for between 24 to 36 hours for hardness scale, and 1 to 4 hours for de-rusting, depending on nature and state of deposits. To avoid saturating the solution, do not exceed a solution strength of 8%.
3. Ensure circuit is vented at the highest point to release gases produced during the descaling operations.
4. Product solution may be heated to increase the descaling process rate up to a maximum of 60°C.
5. Check the acid concentration of the solution regularly by observing its state. If effervescence disappears, the circuit should be drained and a fresh charge introduced.
6. By placing scale samples in easily observed positions, a check on the progress of the descaling operation may be made.When the samples are completely dissolved and effervescence has stopped, circulate for one more hour then drain system thoroughly.
7. Rinse system thoroughly with water then drain.
8. To neutralise any remaining traces of acid and to passivate the circuit, circulate a 1% to 2% by weight solution of ALKALINITY CONTROL or BWT ONE SHOT for 2 to 4 hours. Neutralise acidic effluents drained from the descaling solutions by using ALKALINITY CONTROL until an acceptable pH (5.5 - 7) value is obtained.

Please download Technical Information PDF at link in product's card.

© 2023 Uniservice Unisafe Srl | Marine Chemicals division | www.uniservicemarine.com | Email | T (+39) 010.711.395 | F (+39) 010.713.120

IMPORTANT NOTICE: While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, this information is provided for your guidance only. Because many factors may affect processing or application/use, we recommend that you do a test to determine the suitability of a product for your particular purpose prior to use. No warranties of any kind, either expressed or implied, including warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth, or that the products, designs, data or information may be used without infringing the intellectual property rights of others. In no case shall the descriptions, information, data or designs provided be considered a part of our terms and conditions of sale. Further, you expressly understand and agree that the descriptions, designs, data and information furnished by Uniservice Unisafe Srl hereunder are given gratis, and Uniservice Unisafe Srl assumes no obligation or liability for the description, designs, data and information given or results obtained, all such being given and accepted at your risk.

Rust Remover

Metal Brightener

PART # EA03 | (25L) 0731851223859 / (200L) 0731851223866

PHYSICAL DATA

Appearance: Colorless liquid

Specific gravity: 1.2 @20ºC (average)

pH solution 1% water: 2

Flash Point: None

Corrosive action: Metals: Slight action. Plastic: none

DESCRIPTION

Deoxidising liquid detergent compound containing phosphoric acid and non-ionic surfactants.

• Non-flammable
• Removes light rust and rust stains
• Cleans and brightens aluminium
• Removes tarnish from non-ferrous metals
• Removes rust stains from paint, ceramic and wooden surfaces
• Biodegradable

APPLICATION

• Removal of light rust from iron and steel and brightening of surfaces.
• Removal of tarnish from brass, copper, stainless steel, aluminium, chrome, etc.
• Removal of rust stains from painted surfaces vitreous enamel, porcelain, terrazzo, ceramic tiles, glass, etc.
• Removal of rust stains from wooden surfaces.
• Used as a protective pre-treatment for iron and steel, prior to painting, etc.

ADVANTAGES

• Complete light rust removal.
• Leaves rust and tarnish free surfaces.
• Rapid penetration, wetting and rinsing.
• Inhibited against attack on ferrous metals.
• Forms protective coating on steel surfaces to which paint adheres readily.
• Biodegradable.
• Non flammable.

DIRECTIONS FOR USE

• Remove loose dirt, scale and rust by weeping or brushing prior to use.
• Apply RUST REMOVER to surface to be cleaned as follows:
• Use full strength for severely corroded and soiled surfaces.
• Use diluted in solution of 1 part of RUST REMOVER with 2 to 4 parts of water for aluminium and less severely corroded or soiled surface.
• Scrub surfaces where required.
• Rinse down surfaces with water after 10 to 15 minutes from application. When used on aluminium rinse off within approximately 5 minutes from application.

Note: It is not recommended to use RUST REMOVER on zinc, tin or galvanised surfaces.

Please download Technical Information PDF at link in product's card.

© 2023 Uniservice Unisafe Srl | Marine Chemicals division | www.uniservicemarine.com | Email | T (+39) 010.711.395 | F (+39) 010.713.120

IMPORTANT NOTICE: While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, this information is provided for your guidance only. Because many factors may affect processing or application/use, we recommend that you do a test to determine the suitability of a product for your particular purpose prior to use. No warranties of any kind, either expressed or implied, including warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth, or that the products, designs, data or information may be used without infringing the intellectual property rights of others. In no case shall the descriptions, information, data or designs provided be considered a part of our terms and conditions of sale. Further, you expressly understand and agree that the descriptions, designs, data and information furnished by Uniservice Unisafe Srl hereunder are given gratis, and Uniservice Unisafe Srl assumes no obligation or liability for the description, designs, data and information given or results obtained, all such being given and accepted at your risk.

Lube Oil Separator Cleaner

Disc Cleaner

PART # EA04 | 0731851223873

PHYSICAL DATA

Appearance: Light yellow liquid

Specific gravity: 1.273 kg/L

pH (neat): 1

Solubility in water: Soluble

DESCRIPTION

Special formulated blend of surfactants and acids, designed to remove carbonaceous and varnish deposits from lube and fuel oil separator discs.

• Concentrate blend of surfactants
• Completely soluble in water
• Contains no chlorinated hydrocarbons
• Does not attack stainless steel
• Degreases surfaces and machines parts
• Rapid water rinsing
• Easy to use for fast results

APPLICATION

• To clean separator discs from both lube and fuel oil systems.
• Specifically designed for cleaning stainless steel discs and parts.

ADVANTAGES

• Reduces cleaning time.
• Cost-effective.
• Easily diluted, no mixing.
• Easy to use.
• Dissolved deposits do not re-deposit.
• Safer to use.
• Does not harm discs.

DIRECTIONS FOR USE – PRODUCT DOSE

It is recommended that the discs be immersed in a dilute solution of LUBE OIL SEPARATOR CLEANER. Depending upon the quantity of deposits, a solution containing one part of LUBE OIL SEPARATOR CLEANER to four to eight parts water should be used. Any suitable metal container (except galvanized) or dip tank can be used to clean the parts. The solution can be used at ambient temperature, but faster cleaning will take place at an elevated temperature of 50°- 60°C (122°-140°F).

Do not immerse bronze or brass distributor support columns in the LUBE OIL SEPARATOR CLEANER solution since corrosion of these materials will likely occur. Remove the stainless steel discs from the support column and place only these stainless steel parts in the LUBE OIL SEPARATOR CLEANER solution. After cleaning has be completed, thoroughly rinse the parts with fresh or tap water.

Please download Technical Information PDF at link in product's card.

© 2023 Uniservice Unisafe Srl | Marine Chemicals division | www.uniservicemarine.com | Email | T (+39) 010.711.395 | F (+39) 010.713.120

IMPORTANT NOTICE: While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, this information is provided for your guidance only. Because many factors may affect processing or application/use, we recommend that you do a test to determine the suitability of a product for your particular purpose prior to use. No warranties of any kind, either expressed or implied, including warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth, or that the products, designs, data or information may be used without infringing the intellectual property rights of others. In no case shall the descriptions, information, data or designs provided be considered a part of our terms and conditions of sale. Further, you expressly understand and agree that the descriptions, designs, data and information furnished by Uniservice Unisafe Srl hereunder are given gratis, and Uniservice Unisafe Srl assumes no obligation or liability for the description, designs, data and information given or results obtained, all such being given and accepted at your risk.

Descaler MTA

Sewage Water Systems Descaling

PART # EA05 | 0731851223880

PHYSICAL DATA

Appearance: Dark brown liquid

Average density: 1.15 @20ºC

Flammability: Non flammable

pH (1% solution): 1.2

Corrosive action:: Corrosive on aluminium, zinc and related alloys

DESCRIPTION

Liquid descaler containing a metal corrosion inhibitor.

• Heavy duty carbon remover
• Cleans down to metal surfaces
• Fast and effective usage

APPLICATION

Descaler for any type of metal (except for aluminium and zinc).

ADVANTAGES

• Metal protection through a corrosion inhibitor
• Rapid acid solution action through deep scale penetration

DIRECTIONS FOR USE – PRODUCT DOSE

To be applied: by CIRCULATION or by IMMERSION BATH depending on the size of the equipment to be descaled.

By Circulation:

1) Preparation

• Empty the circuit to be descaled
• Prepare a 50% DESCALER MTA solution
• Install a fume vent at the top of the circuit to be descaled

2) Descaling

• After removing the cleaning solution, gradually add the DESCALER MTA solution. Allow this solution to circulate for approx. 10-12 hours depending on scale thickness.
• During descaling, fumes and foam are formed. When descaling is completed, empty the circuit from the bottom, and, where feasible, remove any scale deposits left with pressure water hose. 3) Rinsing
• Add water to the circuit
• Allow it to circulate for at least 1 hour.

Neutralisation

• Neutralise any acid residues left through circuit passivation with 1%, or 2% if in fresh water, ALKALINITY CONTROL solution allowed to circulate for 2 hours.

By Immersion Bath:

Similar operations as described above:

• Prepare the solution at the required concentration (see paragraph on Dosage)
• Shake the solution (with compressed air or pump) to remove the acid film in contact with the descaled surface.

SAFETY ADVICE

This product is an acid and, although it is inhibited and buffered by a special additive limiting acid fumes, it shall be handled in compliance with recommended safety requirements (i.e. gloves, safety goggles and, in case splashes are possible, apron and boots). In case of contact with eyes, rinse immediately with plenty of water or sodium bicarbonate solution.

DESCALER MTA has demonstrated to the marine industry its unique ability to effectively clean and eliminate uric acid build-ups in sanitation vacuum systems. Ship Owners are turning to Uniservice Unisafe as more and more cruise vessels become faced with clogging problems in their vacuum systems. DESCALER MTA is an on-line solution for eliminating hard deposits which are inherent in vacuum systems formed by uric acid. DESCALER MTA can be introduced by manual dosing into a vessels head or via a simple, yet effective dosing unit. Please contact UNIservice representative for more details.

Special PVC clamp to connect dosing unit injector to sanitary vacuum systems. All sizes of clamps are available to ensure safe connection of dosing unit. O ring gasket to ensure tightness of dosing unit injector to sanitary vacuum systems.

This information is not to be taken as a warranty or representation for which we assume legal responsibility nor as permission, inducement or recommendation to practice any patented invention without a license. The information is offered solely for your consideration, investigation and verification.

Please download Technical Information PDF at link in product's card.

© 2023 Uniservice Unisafe Srl | Marine Chemicals division | www.uniservicemarine.com | Email | T (+39) 010.711.395 | F (+39) 010.713.120

IMPORTANT NOTICE: While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, this information is provided for your guidance only. Because many factors may affect processing or application/use, we recommend that you do a test to determine the suitability of a product for your particular purpose prior to use. No warranties of any kind, either expressed or implied, including warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth, or that the products, designs, data or information may be used without infringing the intellectual property rights of others. In no case shall the descriptions, information, data or designs provided be considered a part of our terms and conditions of sale. Further, you expressly understand and agree that the descriptions, designs, data and information furnished by Uniservice Unisafe Srl hereunder are given gratis, and Uniservice Unisafe Srl assumes no obligation or liability for the description, designs, data and information given or results obtained, all such being given and accepted at your risk.

Safe Descaler Powder

Powdered Acid Descaler

PART # EA06 | 0731851223897

PHYSICAL DATA

Appearance: Pink powder

Apparent specific gravity: 1.2

pH in 1ºh solution in water: 1

Solubility in water: 10% maximum

DESCRIPTION

Water soluble acid powder compound containing descaling accelerators, corrosion inhibitors and indicator dye. * Dissolves water scale and rust scale * Suitable for use with most heating and cooling systems * Improves heat transfer * Non toxic, non explosive

APPLICATION

• Descaling of diesel engine cooling water systems.
• Cleaning and scale removal from air coolers sea water side.
• Water scale and rust scale removal from boilers, condensers, evaporators, heat exchangers, etc.

ADVANTAGES

• Fast and effective scale removal.
• Leaves rust free surface.
• Contains descaling accelerator to increase product action.
• Inhibited against corrosive attacks.
• Contains pH sensitive indicator.
• Rapidly rinsed.
• Powder product -Handling and storage safer and easier.

DIRECTIONS FOR USE – PRODUCT DOSE

Descaling can be accomplished by circulation, for large components and systems, by in-situ soaking, or by soaking in an immersion bath for small components. The most effective method is by circulation as it ensures renewal of acid film in contact with the scale.

Circulation method:

1. If deposits to be removed are covered with an oil or grease film, a degreasing treatment with a solution of 2% to 8% of ALKACLEAN, CARBON REMOVER, SEACLEAN with water should be used prior to descaling, by circulating for 4 to 6 hours up to a temperature of 60°C.
2. After degreasing (where necessary) a descaling treatment of a solution of 5% to 10% by weight of SAFE DESCALER with water should be circulated for between 24 to 36 hours for hardness scale, and 1 to 4 hours for de-rusting, depending on nature and state of deposits. To avoid saturating the solution, do not exceed a solution strength of 10%.
3. Ensure circuit is vented at the highest point to release gases produced during the descaling operations.
4. Product solution may be heated to increase the descaling process rate up to a maximum of 60°C. Over 35°C slight corrosive action may occur on light alloys and galvanised surfaces.
5. Check the acid concentration of the solution regularly by observing its state and colour. Initial colour is pink and if the colour turns yellow, or if effervescence disappears, regenerate the solution by adding more SAFE DESCALER until solution regains initial colour. To avoid the possibility of a saturated solution, no more than 2 additions should be made. If further treatment is necessary the circuit should be drained and a fresh charge introduced.
6. By placing scale samples in easily observed positions, a check on the progress of the descaling operation may be made. When the samples are completely dissolved and effervescence has stopped, circulate for one more hour then drain system thoroughly.
7. Rinse system thoroughly with water then drain.
8. To neutralise any remaining traces of acid and to passivate the circuit, circulate a 1% to 2% by weight solution of ALKALINITY CONTROL for 2 to 6 hours.
9. Neutralise acidic effluents drained from the descaling solutions by using ALKALINITY CONTROL until an acceptable pH value is obtained.

Soaking Method:

• Procedure is similar to that for circulation, i. e. Degreasing, Descaling (ensuring venting), Rinsing and Neutralising.
• The same solution strength should be used.
• If agitation of the descaling solution can be practised, this will help to renew the acid film coming into contact with the scale.

Please download Technical Information PDF at link in product's card.

© 2023 Uniservice Unisafe Srl | Marine Chemicals division | www.uniservicemarine.com | Email | T (+39) 010.711.395 | F (+39) 010.713.120

IMPORTANT NOTICE: While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, this information is provided for your guidance only. Because many factors may affect processing or application/use, we recommend that you do a test to determine the suitability of a product for your particular purpose prior to use. No warranties of any kind, either expressed or implied, including warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth, or that the products, designs, data or information may be used without infringing the intellectual property rights of others. In no case shall the descriptions, information, data or designs provided be considered a part of our terms and conditions of sale. Further, you expressly understand and agree that the descriptions, designs, data and information furnished by Uniservice Unisafe Srl hereunder are given gratis, and Uniservice Unisafe Srl assumes no obligation or liability for the description, designs, data and information given or results obtained, all such being given and accepted at your risk.

UriClean Concentrate

For Removal of Uric Acid Deposit

PART # EA07 | 0731851223903

PHYSICAL DATA

Appearance: Liquid, Clean colorless

Specific gravity: 1.2 @20ºC

pH (1% solution): 1,2

Flash point: None

DESCRIPTION

A unique blend of concentrated biodegradable cleaners for effective removal of uric acid deposits. The development of URICLEAN CONCENTRATE was partly due to the shipowners continual problems, particularly with vacuum type system where uric acid deposits persist and ultimately cause internal blockages. Bacteria products although quite effective on organic wastes, it has been realized that these bacteria type products are ineffective in the reduction or elimination of uric acid deposits. Uric acid deposits crystalize within the internals of a vessels piping system and bacteria can not penetrate the hardened barrier. URICLEAN CONCENTRATE is unique in its formulation and has the proven ability to reduce and in many cases eliminate the concerning problem within a vessels sanitation piping system. With the combined efforts between the ships staff and UNIservice URICLEAN CONCENTRATE can effectively solve the age old problem of line blockages.

• Effectively controls the accumulation of uric acid deposits.
• Effectively removes uric acid deposits.
• Removes lime scale.
• Safe on most common metals.
• Safe on PVC piping.
• Excellent general cleaning capabilities for toilets, sinks, showers and tubs.

PROPERTIES

Liquid containing inhibited acidic properties. URICLEAN is nonflammable and completely soluble in water. It also contains a concentrated blend of biodegradable cleaners. URICLEAN CONCENTRATE has demostrated to the marine industry its unique ability to effectively clean and eliminate uric acid build-ups in sanitation vacuum systems. Ship Owners are turning to Uniservice as more and more cruise vessels become faced with clogging problems in their vacuum systems. URICLEAN CONCENTRATE is an on-line solution for eliminating hard deposits which are inherent in vacuum systems formed by uric acid. URICLEAN CONCENTRATE can be introduced by manual dosing into a vessels head or via a simple, yet effective dosing unit. Please contact Uniservice representative for more details.

ADVANTAGES

• Fast and effective scale removal.
• Leaves rust free surface.
• Contains descaling accelerator to increase product action.
• Inhibited against corrosive attacks.
• Contains pH sensitive indicator.
• Rapidly rinsed.
• Powder product -Handling and storage safer and easier.

DIRECTION FOR USE

• should be used at a rate of 2 ounces (50 ml) of product to each toilet (head) every day.
• can also be used at similar rate in sinks and shower drains.
• is designed to be the first phase in implementing an effective bacteria system on a vessel’s sanitation system.
• unique design will effectively remove uric deposits that exist throughout a vessel’s sanitation system.

Please download Technical Information PDF at link in product's card.

© 2023 Uniservice Unisafe Srl | Marine Chemicals division | www.uniservicemarine.com | Email | T (+39) 010.711.395 | F (+39) 010.713.120

IMPORTANT NOTICE: While the descriptions, designs, data and information contained herein are presented in good faith and believed to be accurate, this information is provided for your guidance only. Because many factors may affect processing or application/use, we recommend that you do a test to determine the suitability of a product for your particular purpose prior to use. No warranties of any kind, either expressed or implied, including warranties of merchantability or fitness for a particular purpose, are made regarding products described or designs, data or information set forth, or that the products, designs, data or information may be used without infringing the intellectual property rights of others. In no case shall the descriptions, information, data or designs provided be considered a part of our terms and conditions of sale. Further, you expressly understand and agree that the descriptions, designs, data and information furnished by Uniservice Unisafe Srl hereunder are given gratis, and Uniservice Unisafe Srl assumes no obligation or liability for the description, designs, data and information given or results obtained, all such being given and accepted at your risk.